Pegler XPress Press-Fit Copper Equal Tee 15mm to 108mm

Pegler XPress Press-Fit Copper Equal Tee

This is an equal tee for water and heating copper, with three ends of the same size, in 15mm, 22mm, 28mm, 35mm, 42mm, 54mm, 66.7mm, 76.1mm, 88.9mm and 108mm.

Push all three pipes fully home before you press any joint, so none of them can pull out as you work.

The Pegler XPress Press-Fit Fittings we hold at Plumb Parts cover 15mm to 108mm.

The same system also covers these fitting types: Copper Straight Couplers, Copper Reducing Couplers, Copper Straight Coupling Slips, Copper Straight Female Connectors, Copper Straight Male Connectors, Copper Male Reducers, Copper Female Adaptors, Copper Male Adaptors, Copper Union Coupling, Copper Equal Elbows, Copper Reduced Elbows, Copper Street Elbows, Copper Knuckle Elbows, Copper Male Elbows, Copper Female Elbows, Copper Back plate Elbows, Copper Long Pattern BackPlate Elbows, Copper 90deg Bends, Copper 45 deg Elbows, Copper Obtuse Street Elbows, Copper Crossover, Copper Partial Crossovers, Copper Full Crossovers, Copper Equal Tees, Copper Reduced Branch tees, Copper One End Reduced Tees, Copper One End Reduced And End Branch reduced Tees, Copper Both End Reduced Tees, Copper Female Branch Tees, Copper Multi Port Female Branch Tees, Copper Stop Ends, Copper Unions, Copper Straight Male Union Connectors, Copper Straight Female Union Connectors.

Whether the job is domestic, commercial or industrial, Xpress copper gives a quick joint without a blowtorch, so the whole installation can be done with one system.

Points worth knowing

• Kitemarked by BSI against BS 8537:2010
• Rated for use from -20°C to 110°C
• Pressure rating of 16 bar over the full temperature range
• Leak Before Press: any joint that has not been pressed shows up as a leak when the system is tested
• Backed by a wide spread of British and overseas approvals
• Rapid jointing cuts labour and time compared with the traditional way
• Because there is no heat, no hot works permit or insurance cover is needed

Specification

• Brand: Pegler XPress
• Range: Xpress Copper (water)
• Maker code: S24; article numbers 38450 (15mm), 38460 (22mm), 38462 (28mm), 38464 (35mm), 38466 (42mm), 38467 (54mm), 38468A (66.7mm), 38469A (76.1mm), 38470A (88.9mm), 38471A (108mm)
• Material: Copper
• Connection: Press Fit ends with EPDM O rings
• Sizes: 15mm, 22mm, 28mm, 35mm, 42mm, 54mm, 66.7mm, 76.1mm, 88.9mm and 108mm
• Standard or approval: BS EN 1254-7 (BSI Kitemark KM 789225)
• Max pressure: 16 bar
• Suitable for: Water services on hard and half-hard copper tube
• Max temperature: -20°C to +110°C

Common Questions

Should I press the tee branch first?

Push all three pipes fully home first, then press each end. That way none of them pull out while you work.

Does an equal tee come in large bore?

Yes, from 15mm up to 108mm, including 66.7mm, 76.1mm and 88.9mm.

Plumb Parts, 555 South Street, Glasgow G14 0QX. Collect in store or have it delivered. Open Mon-Fri 8am-5pm, Sat-Sun 8am-1pm.

Datasheets

• Pegler XPress S24 Product Datasheet (PDF)
• VSH XPress Installation Instructions (PDF)