Pegler XPress Press-Fit Copper One End and Branch Reduced Tee 15mm to 54mm

Pegler XPress Press-Fit Copper One End And Branch Reduced Tee

This is a one end and branch reduced tee for water and heating copper: one run end and the branch are smaller than the other end. It spans 22 x 15 x 15mm up to 54 x 42 x 42mm.

Read the size as full-size end first, reduced end second, branch third. So 22 x 15 x 15mm has a 22mm end, with 15mm on the other end and on the branch. One fitting takes the place of a tee and two reducers. Each end needs the jaw for its own size, so have the right jaws or rings for all of them before you start.

Browse the whole Pegler XPress Press-Fit Fittings range at Plumb Parts, running from 15mm up to 108mm.

Alongside this one, the Pegler XPress Press-Fit system takes in: Copper Straight Couplers, Copper Reducing Couplers, Copper Straight Coupling Slips, Copper Straight Female Connectors, Copper Straight Male Connectors, Copper Male Reducers, Copper Female Adaptors, Copper Male Adaptors, Copper Union Coupling, Copper Equal Elbows, Copper Reduced Elbows, Copper Street Elbows, Copper Knuckle Elbows, Copper Male Elbows, Copper Female Elbows, Copper Back plate Elbows, Copper Long Pattern BackPlate Elbows, Copper 90deg Bends, Copper 45 deg Elbows, Copper Obtuse Street Elbows, Copper Crossover, Copper Partial Crossovers, Copper Full Crossovers, Copper Equal Tees, Copper Reduced Branch tees, Copper Reducing Run Tees, Copper One End Reduced And End Branch reduced Tees, Copper Both End Reduced Tees, Copper Female Branch Tees, Copper Multi Port Female Branch Tees, Copper Stop Ends, Copper Unions, Copper Straight Male Union Connectors, Copper Straight Female Union Connectors.

Xpress copper keeps installation simple. No heat is involved, jointing is rapid, and the same system covers domestic, commercial and industrial pipework.

Why installers choose Xpress

• Rated for use from -20°C to 110°C
• Pressure rating of 16 bar over the full temperature range
• Leak Before Press: any joint that has not been pressed shows up as a leak when the system is tested
• Kitemarked by BSI against BS 8537:2010
• A broad list of British and international approvals applies
• Faster to install than traditional jointing, with less labour
• No flame needed, so no hot works permit or extra insurance is required

Specification

• Brand: Pegler XPress
• Range: Xpress Copper (water)
• Maker code: S27; article numbers 38530 (22 x 15 x 15mm), 38536 (28 x 22 x 15mm), 38532 (28 x 22 x 22mm), 38539 (35 x 22 x 22mm), 38541 (35 x 28 x 22mm), 38542 (35 x 28 x 28mm), 38546 (42 x 35 x 35mm), 38566 (54 x 42 x 42mm)
• Material: Copper
• Connection: Press Fit ends with EPDM O rings
• Sizes: 22 x 15 x 15mm, 28 x 22 x 15mm, 28 x 22 x 22mm, 35 x 22 x 22mm, 35 x 28 x 22mm, 35 x 28 x 28mm, 42 x 35 x 35mm and 54 x 42 x 42mm
• Standard or approval: BS EN 1254-7 (BSI Kitemark KM 789225)
• Max pressure: 16 bar
• Suitable for: Water services on hard and half-hard copper tube
• Max temperature: -20°C to +110°C

Common Questions

How do I read a one end and branch reduced tee size?

The first figure is the full size end, the second the reduced end, and the third the branch. So 22 x 15 x 15mm has one 22mm end with 15mm on the other end and the branch.

Why not use a tee and two reducers?

One fitting replaces three, so there are fewer presses to make and less to go wrong in a ceiling void.

Can I press all three ends with the same jaw?

No, each end needs the jaw for its own size. Have the right jaws or rings for every size on the tee before you start.

Plumb Parts, 555 South Street, Glasgow G14 0QX. Collect in store or have it delivered. Open Mon-Fri 8am-5pm, Sat-Sun 8am-1pm.

Datasheets

• Pegler XPress S27 Product Datasheet (PDF)
• VSH XPress Installation Instructions (PDF)