Pegler XPress Press-Fit Copper Reducing End Tee 15mm to 35mm

Pegler XPress Press-Fit Copper Reducing End Tee

This is a reducing end tee for water and heating copper, where one end of the run is smaller and the branch matches the larger end. Sizes are 22 x 15 x 22mm, 28 x 15 x 28mm, 28 x 22 x 28mm, 35 x 22 x 35mm and 35 x 28 x 35mm.

In 22 x 15 x 22mm, for example, the 15mm end is the reduced one and the branch is 22mm. The middle figure is the reduced run end, so check which end you need reduced when you order. On heating it is useful where a main turns off at a tee and carries on in a smaller size, as it saves fitting a separate reducer.

We carry Pegler XPress Press-Fit Fittings from 15mm through to 108mm.

Fitting types you can pair with it in the Pegler XPress Press-Fit system: Copper Straight Couplers, Copper Reducing Couplers, Copper Straight Coupling Slips, Copper Straight Female Connectors, Copper Straight Male Connectors, Copper Male Reducers, Copper Female Adaptors, Copper Male Adaptors, Copper Union Coupling, Copper Equal Elbows, Copper Reduced Elbows, Copper Street Elbows, Copper Knuckle Elbows, Copper Male Elbows, Copper Female Elbows, Copper Back plate Elbows, Copper Long Pattern BackPlate Elbows, Copper 90deg Bends, Copper 45 deg Elbows, Copper Obtuse Street Elbows, Copper Crossover, Copper Partial Crossovers, Copper Full Crossovers, Copper Equal Tees, Copper Reduced Branch tees, Copper Reducing Run Tees, Copper One End Reduced And End Branch reduced Tees, Copper Both End Reduced Tees, Copper Female Branch Tees, Copper Multi Port Female Branch Tees, Copper Stop Ends, Copper Unions, Copper Straight Male Union Connectors, Copper Straight Female Union Connectors.

For domestic, commercial or industrial pipework, Xpress copper is a tidy all-round system: rapid joints, no naked flame, and matching fittings for the whole run.

Highlights of the system

• BS 8537:2010 compliant and BSI Kitemark approved
• Temperature range of -20°C to 110°C
• Holds a 16 bar pressure rating across the whole temperature span
• Leak Before Press design means a missed joint is picked up at the test stage
• Faster to install than traditional jointing, with less labour
• No flame needed, so no hot works permit or extra insurance is required
• Backed by a wide spread of British and overseas approvals

Specification

• Brand: Pegler XPress
• Range: Xpress Copper (water)
• Maker code: S26; article numbers 38510 (22 x 15 x 22mm), 38512 (28 x 15 x 28mm), 38514 (28 x 22 x 28mm), 38517 (35 x 22 x 35mm), 38518 (35 x 28 x 35mm)
• Material: Copper
• Connection: Press Fit ends with EPDM O rings
• Sizes: 22 x 15 x 22mm, 28 x 15 x 28mm, 28 x 22 x 28mm, 35 x 22 x 35mm and 35 x 28 x 35mm
• Standard or approval: BS EN 1254-7 (BSI Kitemark KM 789225)
• Max pressure: 16 bar
• Suitable for: Water services on hard and half-hard copper tube
• Max temperature: -20°C to +110°C

Common Questions

What is a reducing end tee?

One end of the run is smaller than the other, while the branch matches the larger end. So 22 x 15 x 22mm has a 15mm end and a 22mm branch.

When is it handy on heating?

When a main turns off at a tee and carries on in a smaller size. It saves a separate reducer.

Does the size order matter when ordering?

Yes, check which end you need reduced. The middle figure is the reduced run end.

Plumb Parts, 555 South Street, Glasgow G14 0QX. Collect in store or have it delivered. Open Mon-Fri 8am-5pm, Sat-Sun 8am-1pm.

Datasheets

• Pegler XPress S26 Product Datasheet (PDF)
• VSH XPress Installation Instructions (PDF)